Materials Selection For Automotive Exhaust System Engineering Essay

Materials Selection For Automotive Exhaust System Engineering Essay This assignment looks into the material selection and manufacturing process for an automotive exhaust system considering the operational requirements. Towards the end, the application of alternate material is also discussed. Working Requirements The maximum temperature in an automobile exhaust system is around 750-850 degree celsius. So the selected material for manufacturing the exhaust system should be able to handle temperatures in this range. Also there are various other corrosion factors like high temperature oxidation, de-icing salt contamination and wet corrosion by condensates[mainly towards the tail pipe section]. The exhaust system can mainly be divided into 2 sections based on the working temperature. The hot end[temperatures above 600 degree Celsius] which starts from the manifold till the catalytic converter, and the cold end[temperatures below 600 degree Celsius] which extends from the pre-muffler till the tail pipe. The exhaust system is also subjected to high frequency vibrations due to exhaust gas discharge. Normally, ferrous alloys are used in the manufacturing of exhaust system. These include carbon steel, stainless steel, alloy steels and cast iron. The purpose of adding alloying elements is to help in solid solution strengthening of ferrite, improve the corrosion resistance and other characteristics and the cause the precipitation of alloy carbides. [5] Mild carbon steel was extensively used for the manufacturing of exhaust systems for a considerable period of time. Although mild steel has the properties to withstand exhaust temperature it has very poor corrosion resistance. High exposure to road salt and exhaust condensate can terribly shorten the life span of a mild steel based exhaust system. Also, over the years higher demands in power and environmental safety have seen the demise of mild steel from exhaust systems. Nowadays mild steel is employed in applications where the environment is non-corrosive. Stainless steel has replaced mild steel in exhaust systems today. The ferrous alloying element used here is chromium. The minimum amount of chromium in stainless steel is 10.5%. When stainless steel is heated, chromium forms a protective layer of chromium oxide over the stainless steel surface and delays further oxidation process. The exhaust system in a vehicle is expected to be at its peak performance always and the material failure is a undesirable characteristic for this. Performance and efficiency of a automobile engine is seriously affected by minor changes in the exhaust system. Therefore, it is important that fail proof and efficient materials be used in the construction of automotive exhausts. Materials used for manufacturing of exhaust systems should have the following characteristics: High service temperature, high fatigue strength, high fracture toughness, should be easily machinable and should be economic considering the overall cost of the automobile. Also, the material should be highly resistive to corrosion as the exhaust system is majorly exposed to road salts and condensates from the engine exhaust gases. Failure in the exhaust system can cause loss of back pressure which can significantly affect engine performance parameters.[1] Current trend: Evolution in the automobile industry has also seen the evolution of exhaust systems. From the usual carbon steel exhausts, we can see stainless steel being heavily employed in exhaust systems. From the CES charts, we can see that stainless steel excels over low/medium carbon steel in all properties other than economy. Ferritic stainless steel is used in the manufacture of exhaust systems. Ferritic stainless steel contains chromium as the main alloying element. The percentage of chromium can vary from 10.5% to 18%. These materials are resistant to corrosion and have very low fabrication characteristics. Although, these can be improved by alloying. Grades such as 434 and 444 have improved fabrication properties. Ferritic stainless steel is always used in a annealed state as they cannot be hardened using heat treatment processes. They have vey high resistance to cracking due to stress corrosion. They also exhibit acceptable welding characteristics in thin sections.[1] We can see in detail the different parts of the exhaust system and the material properties below: Exhaust Manifold: The exhaust manifold of a automobile engine is always exposed to hot gases. Cast iron has been in use for the production of exhaust manifolds traditionally. The main characteristics required for the exhaust manifold material include thermal fatigue strength required to withstand the high temperature exhaust gases, oxidation resistance , good fabrication properties and low thermal capacity to enhance the catalytic function. Ferritic stainless steel exhibit all these properties and offers big weight reduction also. The developments in vacuum casting process has helped in the fabrication of stainless steel manifold with section thickness of 2-5mm. Higher demands in pollution control will rise the exhaust temperatures too and therefore, ferritic stainless steel will be in major use for exhaust system manufacturing. Ferritic stainless steel exhibits improves thermal fatigue characteristics when processed by solid solution strengthening with molybdenum or niobium. This process also improve s the oxidation resistance and microstructural stability. Ferritic stainless steel also has cost advantages because of the absence of nickel in its composition. Another variant called the austenite stainless steel is used where ferritic stainless steel is unsuitable. Austenite stainless steel can enhance its properties when enough carbon is added to it. But, the higher cost limits its usage compared to the ferritic variant.[3] Cast iron manifolds can be manufactured by the sand casting process. The solidification of molten cast iron can result in the formation of interstitial voids between the various particles in the cast iron structure. This can lead to particle sliding over each other and as a result a decline in the mechanical properties of the mould. Stress relieving heat treatments are performed inorder to increase the dimensional stability of the material. During heat treatment, the thermal expansion of the material allows the voids to be filled. Although, care should be taken as not to overdo the heat treatment process as too much thermal expansion can bring about more stresses in the material microstructure and this can impair material properties. Changes in microstructure can diminish material properties like thermal fatigue and fracture toughness that can result in the premature failure of the finished product. The alternate material that can be used in exhaust manifold manufacture is ferritic stainless steel. These materials have enhanced properties for exhaust manifold production. The main feature is the low thermal expansion that is one of the major problems faced by cast iron exhaust manifolds. Molybdenum and Niobium alloying has shown tremendous increase in the heat enhancement properties of ferritic stainless steel. Vacuum casting process that is used in the production of ferritic stainless steel manifolds is the factor that increases its cost. Effective methods need to be developed to reduce the tooling and manufacturing cost. Once this is achieved, cast iron exhaust manifolds can be replaced by stainless steel exhaust manifolds that have improved properties and weigh less and can thus adhere to stringent emission norms that come in future. Nowadays stainless steel manifolds are only used in vehicles that call for extreme performance. Commercialisation of this technology is not far a way. Catalytic converter: The catalytic converter is used to clean the exhaust gases and make it free of toxic effects. It is normally exposed to elevated temperatures like 1000 degree Celsius and therefore its durability is a very important factor in proper functioning of the exhaust system. Conventionally the catalytic converters are made of a material called the cordierite monolith that basically acts as the absorbant in it. Cordierite is a silicate and thus the component is manufactured by an extrusion process. Then it is subjected to washcoating where the monolith is submerged in materials such as Al2O3, CeO2, ZrO2 and metals such as platinum, rhodium and palladium. The main properties of the catalytic converter monolith are as follows Fusion point : 1450 degree Celsius Coefficient of Thermal Expansion : 0.002cal/s-cm-oC [low] Thickness of monolith walls : 100 microns Number of cells : 400-900 cpsi The main advantages of the cordierite monolith are lower cost and manufacturing ease. Alternate material for the catalytic converter is stainless steel. Instead of the silicate monolith metal alloy materials are used in the construction of the monolith. These metal monoliths are manufactured by the combination of flat and corrugated layers of the metal alloy. These are then made into the spiral shaped monolith. The exhaust gases escape through the channels formed between the flat and corrugated planes. Washcoating is done in this case also. But the important thing to be remembered is that this process needs to be done before the monolith is made into a spiral shape. This is because the metal monolith is generally smaller in size and that can obstruct the proper washcoating of the entire metallic monolith. The main characteristics of the metallicmonolith are as follows: Fusion point : 1600 degree Celsius [150 degree Celsius more than cordierite] Coefficient of Thermal Expansion : very high[directly influenced by aluminium content in metal alloy] Thickness of monolith walls : 25 microns [less compared to cordierite] Number of cells : 800-1250 cpsi [2] One of the major advantages of the metallic monolith is the high impact resistance. As the catalytic converter is prone to impacts from road surfaces, it is important that the catalytic converter remains intact at all times. The cordierite monolith is very weak compared to metallic monolith in this case. Metallic monoliths also have the advantage of being placed close to the exhaust manifold. This means that they can achieve the operating temperature[around 300 degree Celsius] earlier and thus reduce exhaust contamination. These monoliths can also be developed in smaller sizes compared to the silicate counterparts. Higher service temperature means that metallic monoliths are used in high performance applications where the conditions are very severe. Muffler : The muffler is the final part in the exhaust system. The introduction of catalytic converter has led to the formation of condensates inside the muffler thereby resulting in corrosion. Aluminized carbon steel is employed in the manufacture of the exhaust mufflers traditionally. The exhaust gas condensates have amplified the corrosion rates in the muffler and it is seen that they do not perform to their maximum service life when the catalytic converter is introduced. This normally happens in the short runs of the vehicle where the exhaust gas temperature does not rise high enough to vaporize these condensates. During long runs, the exhaust gas temperature goes over 100 degree Celsius which prevents the formation of condensates and reduces corrosion. Stainless steel mufflers have very high corrosion resistance and the addition of chromium and molybdenum can improve these properties. High production rates can be achieved by the use of stainless steel by tandem mill cold rolling, annealin g and descaling process. Titanium can also be added in small traces to improve muffler properties in stainless steel.[3] Titanium exhaust systems [ a future perspective]: Environmental agencies now prefer guaranteed corrosion resistance on exhaust systems for more than 100,000 miles. Titanium achieves this and is much better than stainless steel systems that are used now. A typical catalytic converter and muffler pipe in stainless steel weighs around 10kg. A redesigned titanium system weighs only around 3.2 kg. This weight saving is very beneficial when considering high performance and high precision automobiles. Pure titanium tube and sheet are the materials of choice for silencers, and pipes. Reduction of weight and cost are achieved by selecting the thinnest gauges of materials consistent with the engineering and acoustic parameters of the exhaust system. Titanium may not be suitable for the entire system, and will most probably be limited to components in which the temperature of metal does not go over 400 degree celsius for longer periods of time. The parts immediately behind the catalytic converter continue to perform well under test. Use of titanium lugs welded to the pipe will certainly prove to be the most efficient method to fix the exhaust to the vehicle frame (via rubber isolators). Material conforming to ASTM Grade 2, (e.g. Timetal 50A) offers the optimum in terms of cost, availability, fabricability, weldability and mechanical properties. Grade 45A is slightly less strong and more ductile than 50A and may be required where extensive forming is part of the manufacturing process e.g. lock seaming (Table 4). Both alloys are fully weldable, require no intermediate or post-forming heat treatment, and are available in wide sheet coil. These alloys are also used to manufacture low-cost continuously welded tube.   Properties of pure titanium 45A and 50A 45A 50A Thermal expansion (10-6degree Celsius) 8.9 8.9 Hardness (HV) 140-170 160-200 Tensile Modulus ( 103N.mm2) 103 103 Density ( g.cm-3) 4.51 4.51 Specific Heat( J.kg-1.oC-1) 519 519 RA min (%) 40 35 Titanium Production: Pure titanium is cold formable, and sheets or tube can be shaped readily at room temperature using techniques and equipment that are normally for steel. Following factors must be taken into consideration while machining titanium.  ·Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  The ductility of titanium is generally less than that of steel. More generous bend radii may be required during bending applications.  ·Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  The modulus of elasticity of titanium is about half that of steel. This means that titanium will return back to original state after forming. Compensation for this can be done by slight overforming.  ·Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Titanium tends to gall against unlubricated forming tools. Proper lubrication of the tool can solve this problem. Both lock seaming and resistance welding are suitable to join the catalytic converter, and traditional TIG is suitable to seal the ends and pipe joints with a torch trailing shield to the external surface of the box end joints. Production Economy: A leading exhaust system manufacturer in the United States, successfully rolled and seam welded a batch of titanium boxes at one of its production units. This was done with no extra cost when compared with the production of steel components. It was also seen that the bending units that are currently employed for the bending of steel are suitable in the case of titanium also. The only factor is the procurement cost of titanium and therefore significant efforts are necessary to bring down tooling and manufacturing costs.[3] Conclusion: It can be concluded that stainless steel can replace conventional materials in automotive exhaust systems. We have to count on developments in tooling and manufacturing methods that can bring down overall costs to minimum. Stainless steel is easily the best alternative in service aspects of the exhaust system. High performance materials like titanium may also come into commercial production soon. Improved thermal, mechanical and chemical properties are major factors that govern material selection for an exhaust system.

Assess The View That The Nuclear Family Is No Longer The Norm

The nuclear family was commonly seen in many countries of the world due to its practicality and replaced the extended family in most societies. The nuclear family is defined by George Peter Murdock as a married male and female couple raising one or more children in one household.This structure became the norm in modern society as it fulfils Murdock’s 4 functions of the family: Sexual; helps maintain a healthy and stable relationship between the parents, Reproductive; to continue the population and produce workers for society, Economic; to support the family by working in society and sharing roles between the man and woman, Education; to serve as a source of primary socialisation for children so that they may function properly in society. Sociobiologists believe that our behaviour is due to biological instincts.The nuclear family proved that it worked so was continued to be used as it was seen crucial to the survival of our species and zoologist, Desmond Morris mentioned that à ¢â‚¬ËœMost successful cultures use the nuclear family’. The ‘cereal packet family’ is a term given by Edmund Leech in 1967 when he recognised the power of the image of the nuclear family. It’s a socially constructed model laden with assumptions of how families ought to be. Such an image creates a normalised social construction of what a family should look like. However, many other family structures are being used which suggests that the nuclear family is not the norm.For example, the Kibbutz lived in an extended family structure, meaning that their entire family lived together and not just their immediate family. The Nayar tribe are an example of people who used the extended family due to living in poverty. The wives would get support from family members and work together to raise the children whilst the men would go out and provide for the family. Felicity Edholm critiqued Murdock’s idea of the nuclear family by saying, ‘the family is sociall y constructed. ’ This means that it has varied from culture and is also not biological for humans.Therefore, Murdock defined the nuclear family from his cultural perspective and completely ignored others. Edholm referred to this as ‘The Unnatural Family’. In the UK today, many other family structures are in place due to a number of things. Since the early 1990s, divorce rates have increased by a fair amount, creating lone-parent families. This also led to a lot of people remarrying, creating reconstituted (step) families. These go against Murdock’s nuclear family due to having both parents living separately or having children from different relationships.In fact, these family structures have become more common than the nuclear family itself. Recently, same sex marriages have been approved in many places around the world, allowing gay couples to start families of their own. This also goes against Murdock’s idea of the nuclear family which involved a couple each of a different sex. In conclusion, the nuclear family is no longer considered the norm due to mass increase of lone-parent and reconstituted families because of a divorce being extremely to get. Although the nuclear family may well work and be very practical in society, it just isn’t easily accessed by many people.

Creative Writing My Own Idea of God - 913 Words

I closed the door behind me. Fitting it should rain on such a day, long strides as to avoid running. I latched the gate one last time and approached my car. And though the thought had occurred to me before that day, that this car would become my home, I was not prepared to be homeless. If I cared to add another to the list, that car would become the 30th home in 37 years. It goes without saying I never really had a home and I did not feel as if I were leaving my home. Of course I had comfort, convenience and safety. As an artist I could not imagine life without a wall to tack my canvas, a floor to sit and meditate, or a stove to satisfy my passion for the culinary arts. But as a human being I knew the things in my life were no more a privilege than a burden or a vice. As I sat in my new home I stepped back through all my comforts, all my love, my family, my career, my passions and I did not stop at my childhood. I thought of the innocence and the happiness. I became consumed with my ignorant and innocent hope. An hour or so had passed and I still hadnt moved on, but to where would I need to move? It would eventually be that contemplation, still dry from the quiet rain, that would push me from that place with no place to go. To say I became homeless in that moment is only relevant to the statement one without a home, and still it is relative only to the conventional idea of homelessness. I had a job, money, a car, bills, food, and though diminished I retained a levelShow MoreRelatedAnalysis Of The Book Carte Blanche Essay1479 Words   |  6 Pagesare all elements I considered when drafting ‘Time to let go.’ This narrative is not a direct recollection of my personal experience. But, interprets a devastating chain of events that happened to my son’s friend, and the effect this tragic accident had on a mother. I wanted to tell this story with as much sentiment and compassion as possible. Therefore, I relied on a variety of ‘creative el ements’ to coalesce understanding, memory and imagination. To bring together the feelings and emotions ofRead MoreMy Writing Skills Have Improved Since Freshman Year1252 Words   |  6 PagesThe pieces say that as a student I put the effort that I can into my work. I try my best to finish the in class writing in time and to put effort and creativeness into the creative writing pieces. Looking at my hand written work, I need to slow down and try to write more legibly because I am not showing my best handwriting in those pieces. I am proud of my Fall/Spring benchmark grades, but I can work to improve. In the process of creating I learned that there can be multiple answers and perspectivesRead MoreA Speech On Cornerstone Education1008 Words   |  5 Pagesreceived my Associates degree in Business this week, I am thrilled by this accomplishment. I did not plan that I would finish, I thought that I would enjoy each moment of this journey without expectations and I did. The Professional and Graduate Studies program at Cornerstone University has enriched my life with the freedom to write in my worldview, to reflect creatively, and invited a new way of being outside my inner circle that has opened a bigger world. The freedom to write from my worldviewRead MoreAn Essay About Greek Gods And Goddesses939 Words   |  4 Pages Have you ever tried writing a paper and realized that you weren’t really getting anywhere? I know I sure have! It was in about eighth or ninth grade, which seems along the lines of forever ago but also shows how much this specific writing assignment affected me, even until this day. I experienced what it feels like to have writer’s block for the first time. It ended up helping me in the long wrong, though, after collecting a large amount of information. So, don’t get discouraged if you find yourselfRead MoreA Speech On Cornerstone Education1086 Words   |  5 Pagesreceived my Associates degree in Business this week, I am thrilled by this accomplishment. I did not plan that I would finish, I thought that I would enjoy each moment of this journey without expectations and I did. The Professional and Graduate Studies program at Cornerstone University has enriched my life with the freedom to write in my worldview, to reflect creatively, and invited a new way of being outside my inner circle that has opened a bigger world. The freedom to write from my worldviewRead More The Colour Purple and The Yellow Wallpaper1666 Words   |  7 Pagesoppression, of presenting self in opposition to a language which is not your own. Explain how this statement informs your reading of The Colour Purple (TCP), and The Yellow Wallpaper (TYW). In TCP, written in first person narrative, Walker uses the epistolary style of writing, giving authority to the voice of Celie and enabling the reader to accept her as having real presence and experience. In her opening letter to God, it is obvious she has no self-confidence, crossing herself out with aRead MoreI ve Been Feeling Like A Beta Author Who Supplies Occasional Story1429 Words   |  6 Pagesoccasional story ideas and grammatical and stylistic edits to our fics, rather than a full-fledged co-creator. We both know that many of my feelings are irrational, and are deeply rooted in my own insecurities in my worth as an independent human being. However, the fact is that I feel the way I do, no matter how absurd these feelings may seem to you and me. I do think that at least some of these feelings have tangible sources that, if you’ll permit me, I will attempt to explain. The crux of my feelingsRead MoreThe Importance Of Writing My Life Story986 Words   |  4 Pageshad to construct our very own â€Å"life story† sent me into a frenzy. However, I slowly began to think about whether I would write something based on my own experiences or the experiences of a fictional character considering it was my first time writing a story about my life or someone else for that matter. Writing about my life experiences or the emotions that come along with such experiences was never something that I fancy. To my surprise, I eventually choose to write my own life story with a figurativeRead MoreWe Talk About Love By George Saunders And Lance Olsen1334 Words   |  6 Pagesneeded to change some of my static habits. One of these conventions was consuming the same type of literature year after year and not allowing myself enough time to write. So I began taking recommendations from peers I respected and read works from writers I had met. Raymond Carver, Junot Dà ­az, Colum McCann, Anne Lamott, Sherman Alexi, Dorothea Brande, George Saunders and Lance Olsen are a handful of the writers I discovered. All have affected my own writing, but after reading many worksRead MoreHow Dialogue And The Stage Affects An Audience s Perception1269 Words   |  6 Pagesbut I feel that I have honed my dramaturgical analysis. I really enjoyed this semester, and I have definitely improved as a playwright. I broadened my abilities as both a reader and a writer. My dialogue has developed further, becoming more varied and rich. I have also learned how to harness my creativity more easily, creating more of a story in my writing than I had previously thought was possible. The plays we read this semester gave me ample opportunity to expand my insights both as a reader and

The Use Of Alzheimers Disease - 1201 Words

There’s now a new smartphone app designed to help doctors diagnose Alzheimer’s disease. Diagnosing Alzheimer’s isn’t easy. Because of the complexity of the disease, there are a ton of different factors that contribute to the process. With every visit, doctors need to ask hundreds of questions about the patient to collect every piece of information that could be used as clues to a diagnosis. This makes dementia evaluations very lengthy and exceedingly inconvenient for the patient as well as the doctor. What makes this even worse is the time spent having to collect lots of information, which leaves significantly less time for healthcare providers to counsel their patients once a diagnosis is made. Counseling and support are equally†¦show more content†¦A new app has emerged to help doctor’s collect information from their patients. A new app has now been created to help doctors with this task. It collects simple information from the caregivers before the patients even physically see their doctor. This new ability to get a lot of important information more rapidly helps doctors make diagnoses quicker yet still with confidence. In doing so, they can hopefully spend more time with patients explaining the diagnosis and discussing treatment options. What an amazing app. Can you believe it was designed by students? This innovative app was actually designed by a research team led by students from the Washington University School of Medicine in St. Louis, Missouri. They are part of a group called Memento, which is a student-run organization at their school. These ambitious students come from a variety of fields of study, with expertise in medicine, basic sciences, and engineering. They collaborated together to pool their talents and design this very helpful online app. The app design The research team created the app based on the most common tool used in dementia diagnosis. The tool is a complex questionnaire known as the Clinical Dementia Rating Scale (CDR), which was also developed at the Washington University School of Medicine. The CDR evaluates each patient’s likelihood of having dementia. It does this by using specific questions to gain insight in 6 domains related to aShow MoreRelatedAn Example Of A And A Neurocognitive Disorders And How They Affect Personality And Behavior Essay1470 Words   |  6 Pagesspeech-language therapy works to help improve communication skills and use language more effectively. Third, occupational therapy help find ways to adapt every day tasks and obstacles, to make them match person’s abilities. And finally, emotional and behavioral therapy works to help the person to find appropriate responses to both desirable and undesirable behaviors (Kennedy, 2014). Another approach to helping people with Down Syndrome is through the use of drugs and supplements. Some doctors will prescribe aminoRead MoreAlzheimer s Disease And Its Relationship With Personality1235 Words   |  5 Pages Alzheimer’s Disease and its Relationship with Personality By: Kristen Hughes The point of this literature review is to explore the relationship that Alzheimer’s disease has with one’s personality. There are many changes that happen to a person as they age, a lot of which are considered a normal part of aging. Being diagnosed with Alzheimer’s disease is not one of those changes that is considered normal (Hoyer Roodin, 2009). Alzheimer’s disease (AD) is a form of dementia that is characterized byRead MoreAlzheimer s And The Most Relevant Cause Of Dementia1496 Words   |  6 Pages Alzheimer’s, the most relevant cause of Dementia, is a disease that affects as many as 4.5 million Americans per year (WebMD 2005-2014). Alzheimer’s is a disease that is an irremediable, continuous brain neuron degenerative disease that can be asymptomatic at first and then overtime becomes symptomatic. Alzheimer’s is a gradual disease that advances in three phases: mild, then moderate, and, finally, severe (1). Symptoms appear after the age of 60 and include: the slow destruction of memory andRead MoreImagine One Day You Wake Up And Suddenly You Don’T Know1420 Words   |  6 Pageshappens to Alzheimer’s patients: they slowly begin to lose their memory. In the beginning, it’s little things with memory, but they don’t seem to have a huge effect on everyday life. Then, it moves on to greater memory loss, beginning to affect daily tasks, causing them to ask multiple questions and take longer to complete daily tasks. As they continue to progress through the disease, they lose all memory and have an extremely hard time with seemingly easy things. In the final stage of the disease, theRead MoreSymptoms And Symptoms Of Alzheimer s Disease1642 Words   |  7 Pages Abstract Alzheimer’s disease is a brain disorder when brain cells degenerate and die. Alzheimer’s dieses destroys the patient’s memory within time. The mental functions of the brain also get destroyed when a person gets Alzheimer’s. Alzheimer’s disease is most commonly seen when the patient is sixty to seventy years old. In this research paper the reader will learn about the signs and symptoms, causes, course of disease, outcome and secondary diagnosis, treatment, and prognosis and survivalRead MoreAlzheimer s Disease : A Type Of Dementia910 Words   |  4 Pages Alzheimer’s disease Jordyn Marcx Anatomy Physiology 2 Professor Leal November 12, 2015 Abstract: Alzheimer’s disease is a type of dementia that causes problems with memory, thinking and behavior. Symptoms usually develop slowly and get worse over time. Alzheimer s is the most common form of dementia, a general term for memory loss. Alzheimer s disease accounts for 60 to 80 percent of dementia cases. Alzheimer’s disease attacks the brain’s nerve cells causing memory loss. Alzheimer’sRead MoreAlzheimer s Research Paper : Alzheimer And Its Symptoms1703 Words   |  7 PagesMrs. Crow 18 November 2015 Alzheimer’s Research Paper There are three separate stages of Alzheimer’s, they are all so different and yet so similar. Many people have a false recollection of Alzheimer’s disease and its symptoms. Many believe that people only get Alzheimer’s as a result of aging. Alzheimer’s disease is not a disease that happens because the human body gets worn down, but because of a change occurring in the human brain. Alzheimer’s is a serious disease that needs to to be acknowledgedRead MoreAlzheimer s Disease Is The Most Common Form Of Dementia1684 Words   |  7 Pages Alzheimer’s disease is the most common form of dementia, which slowly and steadily impairs the mental function and psychological competence. Even though there is no cure for Alzheimer’s, current treatment patterns and research aim to delay the progression towards dementia and the associated symptoms. The strongest risk factor for this disease is increased age, typically seen in individuals over the age of 65, but it must be noted that Alzheimer’s is not a normal part of the aging process. AlzheimerRead MoreAlzheimer s Disease : My Grandma s Killer1354 Words   |  6 PagesAlzheimer’s Disease: My Grandma’s Killer Alzheimer’s Disease (AD) is characterized by gradual cognitive decline that beings with the inability to create recent memories or thoughts, which then proceeds to effect on all intellectual functions (Mayeux Stern, 2012). AD affects an estimated 5.5 million people in the United States, and 24 million people worldwide (Mayeux Stern, 2012). The incidence of Alzheimer’s disease is rising in line with the aging population, therefore; AD is most common inRead MoreInstagram899 Words   |  4 PagesAlzheimer’s disease is one of the most frequent causes of dementia (weak-mindedness) at elderly and senile age. Dementia is characterized by the expressed decline of intellectual functions of the person with ability disorders of surrounding conditions and independent actions. The disease is called by the name of A. Alzheimer, who described this form of illness in 1906. In the absence of treatment the disease steadily progresses and leads to the destruction of all mental functions. The etiologies